WarningCode

class ansys.meshing.prime.WarningCode(value)

Warning codes associated with the PyPrimeMesh operation.

Methods

WarningCode.conjugate	Returns self, the complex conjugate of any int.
WarningCode.bit_length(/)	Number of bits necessary to represent self in binary.
WarningCode.bit_count(/)	Number of ones in the binary representation of the absolute value of self.
WarningCode.to_bytes(/, length, byteorder, *)	Return an array of bytes representing an integer.
WarningCode.from_bytes(/, bytes, byteorder, *)	Return the integer represented by the given array of bytes.
WarningCode.as_integer_ratio(/)	Return integer ratio.

Attributes

WarningCode.real	the real part of a complex number
WarningCode.imag	the imaginary part of a complex number
WarningCode.numerator	the numerator of a rational number in lowest terms
WarningCode.denominator	the denominator of a rational number in lowest terms
WarningCode.NOWARNING	No warnings.
WarningCode.UNKNOWN	Unknown warning.
WarningCode.SURFER_QUADCLEANUP_MULTITHREADINGNOTSUPPORTED	Multithreading is not supported for quad cleanup operation.
WarningCode.OVERRIDECURVATURESIZINGPARAMS	Overriding curvature sizing parameters.
WarningCode.OVERRIDESOFTSIZINGPARAMS	Overriding soft sizing parameters.
WarningCode.OVERRIDEHARDSIZINGPARAMS	Overriding hard sizing parameters.
WarningCode.OVERRIDEPROXIMITYSIZINGPARAMS	Overriding proximity sizing parameters.
WarningCode.OVERRIDEBOISIZINGPARAMS	Overriding BOI sizing parameters.
WarningCode.OVERRIDEMESHEDSIZINGPARAMS	Overriding meshed sizing parameters.
WarningCode.INVALIDSIZECONTROLSCOPE	Invalid size control type provided.
WarningCode.OVERRIDEGROWTHRATEPARAM	Overriding growth rate parameter.
WarningCode.OVERRIDESUGGESTEDNAME	Override name by suggested name.
WarningCode.OVERRIDESURFACESCOPEENTITY	Override surface scope entity.
WarningCode.OVERRIDEVOLUMESCOPEENTITY	Override volume scope entity.
WarningCode.MAXOFPRISMCONTROLSMINASPECTRATIO	Maximum value of min aspect ratio from selected prism controls is considered for all selected prism controls.
WarningCode.OVERRIDEEDGESCOPEENTITY	Override edge scope entity.
WarningCode.SHELLBLGAPFACTORMINLIMIT	Adjusted ShellBL gap factor to 0.001.
WarningCode.PARTNOTINPARTSCOPE	Selected part is not in the part scope of the periodic control.
WarningCode.NUMERICPARTNAMERENAMETOALPHANUMERIC	Numeric part name renamed to alphanumeric name.
WarningCode.SURFERLAYEREDQUADFAILED	Layered quad failed with surfer.
WarningCode.SURFERDEGENERATEFACE	Degenerate input.
WarningCode.ALIGN_OPERATIONINTERRUPTED	Align operation interrupted.
WarningCode.FUSEOVERLAPREMOVALINCOMPLETE	Self intersections found.
WarningCode.REMOVEOVERLAPWITHINTERSECT	Self intersections found.
WarningCode.IGA_NOGEOMZONELETFORSPLINEFITTING	Invalid input for IGA.
WarningCode.NOHOLESFOUNDONPLANE	Provides warning when no closed holes are found in the given face zonelets at given plane.
WarningCode.NOVOLUMESCOMPUTED	There are no volumes found.
WarningCode.EXTERNALOPENFACEZONELETSFOUND	External open face zonelets found when computing volumes.
WarningCode.NOVOLUMESENCLOSINGMATERIALPOINT	No computed volumes enclosing material point.
WarningCode.EXTERNALOPENTOPOFACESFOUND	External open topofaces found when computing topovolumes.
WarningCode.FACEZONELETSWITHOUTVOLUMES	Face zonelets have no volume associated to them.
WarningCode.JOINEDZONELETSFROMMULTIPLEVOLUMES	Joined zonelets from more than two volumes.
WarningCode.FAILEDTOUPDATEVOLUMES	Volumes are not updated after performing the operation.
WarningCode.WRAPPER_SIZECONTROLNOTDEFINED	No size controls provided for wrapper.
WarningCode.WRAPPER_SIZECONTROLNOTSUPPORTED	Size control is not supported in wrapper.
WarningCode.WRAPPER_SMALLERSIZEATFEAURES	Size at features is smaller than base size.
WarningCode.WRAPPER_SMALLERCONTACTPREVENTIONSIZE	Contact prevention size is smaller than base size.
WarningCode.MATERIALPOINTWITHSAMENAMEEXISTS	Material point with the same name exists.
WarningCode.ENTITIESNOTBELONGTOANYZONE	Entities do not belong to any zone.
WarningCode.INVALIDENTITIESNOTADDEDTOZONE	Entities with invalid id or type not added to zone.
WarningCode.LOCALSURFERNOFACEREGISTERED	No face registered with the given register id.
WarningCode.MESHHASNONPOSITIVEVOLUMES	Mesh has non positive volumes.
WarningCode.MESHHASNONPOSITIVEAREAS	Mesh has non positive areas.
WarningCode.MESHHASINVALIDSHAPE	Mesh has invalid shape.
WarningCode.MESHHASLEFTHANDEDNESSFACES	Mesh has invalid shape.
WarningCode.NOCADGEOMETRYFOUND	CAD geometry not found for some or all topo entities.
WarningCode.NOCADGEOMETRYPROJECTONFACETS	CAD geometry not found for some or all topo entities.
WarningCode.DUPLICATEINPUT	Duplicate items in input.
WarningCode.UNPROCESSEDKEYWORDSINABAQUSFILE	Unprocessed Abaqus keywords have been found.
WarningCode.EXPORTMAPDLANALYSISSETTINGSFAILED	Export MAPDL analysis settings failed.
WarningCode.WRITINGCONTACTPAIRSSKIPPED	Writing of contact pairs skipped.
WarningCode.WRITINGTIESSKIPPED	Writing of ties skipped.
WarningCode.WRITINGZONELETOFLABELTOELEMENTCOMPONENTSKIPPED	Writing of zonelet skipped while exporting label as element component.
WarningCode.VT_SKIPPEDPROTECTEDENTITIES	Input contains protected entities which have been skipped.
WarningCode.VT_SKIPPEDFEATUREENTITIES	Input contains feature entities which have been skipped.
WarningCode.VT_SKIPPEDFREEEDGES	Input contains free edges which have been skipped.
WarningCode.VT_SKIPPEDNONMANIFOLDEDGES	Input contains non-manifold edges which have been skipped.
WarningCode.VT_SKIPPEDENTITIESINDIFFERENTZONES	Input contains entities in different zones which have been skipped.
WarningCode.VT_CANNOTMERGENODES	Cannot merge nodes during VT operation.
WarningCode.VT_REMESHFACEFAILED	Failed to remesh face(s) during VT operation.
WarningCode.MULTIZONEMESHER_SURFACESCOPEVOLUMESCOPEINCONSISTENCY	MultiZone warning codes